Authors

Yusuf Umardani

Mechanical Engineering Department, Diponegoro University, Semarang, Indonesia

Agus Suprihanto

Mechanical Engineering Department, Diponegoro University, Semarang, Indonesia

Dani Dwi Prasetyo

Mechanical Engineering Department, Diponegoro University, Semarang, Indonesia

Abstract

The mechanical integrity of welded carbon steel exposed to acidic environments depends on weld-zone heterogeneity, local hardness characteristics, and joint discontinuities. This study evaluates the changes in Vickers microhardness and tensile strength of gas metal arc welded (GMAW) SS400 carbon steel after immersion in 0.5 M sulfuric acid (H₂SO₄). Four exposure conditions were considered: 0, 7, 14, and 21 days at 27 ± 2 °C. Hardness was measured in the weld metal (WM), heat-affected zone (HAZ), and base metal (BM), while tensile response was evaluated using maximum load and ultimate tensile strength (UTS). The results show that WM hardness ranged from 201.08 to 213.53 HV0.3 and HAZ hardness ranged from 169.99 to 184.46 HV0.3, with no monotonic decrease as immersion time increased. BM hardness exhibited a larger variation, decreasing from 227.60 HV0.3 in the unexposed condition to 161.61 HV0.3 after 21 days. The mean UTS values at 0, 7, 14, and 21 days were 396.50, 348.21, 351.81, and 414.25 MPa, respectively, showing a non-monotonic response. All eight tensile specimens fractured within the weld region, including the unexposed specimens. The UTS variation and fracture locations indicate that initial joint quality and possible welding discontinuities should be considered when interpreting the effect of acid exposure. Given the limited number of tensile specimens, a causal relationship between immersion time and tensile-strength changes cannot be established.

Keywords

SS400 GMAW Vickers microhardness tensile strength fracture behaviour sulfuric acid

Citation of this Article

Yusuf Umardani, Agus Suprihanto, & Dani Dwi Prasetyo. (2026). Mechanical Properties and Failure Behavior of GMAW-Welded SS400 Carbon Steel after Immersion in Sulfuric Acid Solution. Current Journal of Engineering and Science Research. 3(11), 9-15. Article DOI: https://doi.org/10.47001/CJESR/2026.311002 

Licence Copyright (c) 2026 Current Journal of Engineering and Science Research. This work is licensed under a Creative Commons Attribution Non Commercial 4.0 International Licence.

References

  1. American Welding Society. (2020). AWS A5.18/A5.18M: Specification for Carbon Steel Electrodes and Rods for Gas Shielded Arc Welding. American Welding Society.
  2. American Welding Society. (2020). AWS D1.1/D1.1M: Structural Welding Code—Steel. American Welding Society.
  3. ASTM International. (2021). ASTM E8/E8M-21: Standard Test Methods for Tension Testing of Metallic Materials. ASTM International.
  4. ASTM International. (2021). ASTM E384: Standard Test Method for Microindentation Hardness of Materials. ASTM International.
  5. ASTM International. (2021). ASTM G31-21: Standard Guide for Laboratory Immersion Corrosion Testing of Metals. ASTM International.
  6. Chen, H., Li, Y., Liu, H., & Xiong, Y. (2026). Corrosion behavior and static tensile properties of butt-welded joints considering stress conditions and artificial seawater. Ocean Engineering, 343, 123110. https://doi.org/10.1016/j.oceaneng.2025.123110
  7. Dong, Y., Liu, D., Du, H., Sun, H., & Zuo, X. (2023). Effect of microstructure on the mechanical properties and corrosion resistance of a welded joint of 620-grade marine steel. Frontiers in Materials, 10, 1107125. https://doi.org/10.3389/fmats.2023.1107125
  8. Jatimurti, W., Prahasto, N. A., & Wibisono, A. T. (2023). Effect of current and electrode diameter of gas metal arc welding (GMAW) on mechanical properties and microstructures of JIS G3101 SS400. AIP Conference Proceedings, 2592, 020014. https://doi.org/10.1063/5.0129702
  9. Japanese Standards Association. (2020). JIS G3101: Rolled Steels for General Structure. Japanese Standards Association.
  10. Kou, S. (2003). Welding Metallurgy (2nd ed.). John Wiley & Sons.
  11. Lahouel, A., Athmani, S., Sedik, A., Saoudi, A., Barille, R., Khezami, L., Guesmi, A., & Fellah, M. (2025). Predictive correlation between hardness and tensile properties of submerged arc welded API X70 steel. Materials, 18(19), 4482. https://doi.org/10.3390/ma18194482
  12. Mokhtari, E., Heidarpour, A., & Javidan, F. (2024). Mechanical performance of high strength steel under corrosion: A review study. Journal of Constructional Steel Research, 220, 108840. https://doi.org/10.1016/j.jcsr.2024.108840
  13. Pavlina, E. J., & Van Tyne, C. J. (2008). Correlation of yield strength and tensile strength with hardness for steels. Journal of Materials Engineering and Performance, 17, 888–893. https://doi.org/10.1007/s11665-008-9225-5
  14. Poonnayom, P., Chantasri, S., Kaewwichit, J., Roybang, W., & Kimapong, K. (2015). Microstructure and tensile properties of SS400 carbon steel and SUS430 stainless steel butt joint by gas metal arc welding. The International Journal of Advanced Culture Technology, 3(1), 61–67. https://doi.org/10.17703/IJACT.2015.3.1.61
  15. Revie, R. W., & Uhlig, H. H. (2011). Uhlig's Corrosion Handbook (3rd ed.). John Wiley & Sons.